Radiant comfort you can design around — nothing to hide.
For interior designers and architects specifying comfort for high-end clients. Waterless radiant frees your interiors from radiators, baseboards, and wall units — the floor itself is the heat source. A thin build-up protects ceiling heights and sightlines, summer cooling runs through discreet air handlers, and there's no in-slab water to leak beneath finished floors.
Will heating hardware show in the space?
No — there are no radiators, baseboards, registers, or wall units. The floor itself radiates heat, so the interior stays clean and reads exactly as designed.
Common Home Designers & Architects Challenges
We understand the unique production challenges your industry faces. Here's how we address them.
The climate system becomes the thing you have to hide
In a considered interior, conventional equipment fights the architecture: registers in the ceiling, returns in the wall, mini-split heads above the trim. Waterless radiant warms each room invisibly from the floor itself, so heating leaves no mark on the design and the rooms read exactly as drawn.
Forced air is never as quiet or even as a fine interior deserves
Clients notice the rush of a vent, a warm ceiling over a cold floor, the dust that follows blown air. Radiant heat removes the noise and drafts entirely, holding rooms steady to about ±1 °F at roughly 20 dB(A).
Water under a finished floor is a risk worth designing out
Hydronic radiant runs heated water through the floor, and the failures owners fear most — leaks into a finished slab, scale, and pipes that freeze and burst — all begin with that water. Our floor loop carries refrigerant through weld-free, corrosion-resistant copper, pressure-tested gas-tight before the floor is closed.
Solutions Built for Home Designers & Architects
Invisible warmth, complete design freedom
The copper loop network adds only about 1 to 2 inches of floor build-up and disappears entirely beneath the finished surface. With no radiators, baseboards, or heating vents to place, you keep every wall, window, and sightline, and the client gets even, draft-free warmth underfoot.
Waterless Radiant Floor Heating →One quiet platform for heat, cooling, and hot water
A single inverter air-source heat-pump platform delivers waterless radiant heat in winter, cooling and fresh air through slim matched air handlers in summer, and domestic hot water year-round, with a COP up to 4.6. You specify one coordinated system rather than a basement of separate boilers and units.
Heat, Cool & Hot Water — One System →Per-room comfort, managed from an app
Each room can hold its own temperature, controlled independently and managed from an app, so comfort follows how the home is actually lived in without a thermostat on every wall to disrupt the space.
Smart Zoning & App Control →Products for Home Designers & Architects
Waterless Radiant Floor Heating
Refrigerant-direct radiant with only about 1 to 2 inches of floor build-up and no boiler, buffer tank, pump, or water in the floor. Invisible, draft-free warmth from the floor itself, rated to perform down to minus 13 degrees Fahrenheit with a COP up to 4.6.
Two-in-One Heating + Cooling
Waterless radiant floor heat in winter plus cooling and fresh air through slim, matched air handlers in summer, all on one refrigerant platform. Heating is delivered invisibly through the floor; cooling and humidity are managed by quiet indoor air handlers, never a chilled floor.
5-Constant Comfort
An integrated standard that holds temperature, humidity, fresh air, cleanliness, and quiet steady at once — about ±1 °F swing, roughly 20 dB(A), and 40 to 60% relative humidity — so the interior simply feels right all year.
A designer-led custom home kept serene, even, and free of visible hardware
Challenge
A design team specifying a large custom residence wanted uninterrupted walls and floors — no radiators, registers, or wall units to break the architecture — with even, quiet comfort and no water running through the finished floors.
Solution
The home was designed around a two-in-one platform: far-infrared waterless radiant floors delivering invisible, draft-free heat through weld-free copper loops, with cooling, fresh air, and humidity handled by slim matched air handlers, all driven by a single inverter air-source heat pump and zoned room by room.
Result
The finished interiors show no heating hardware, hold steady even comfort across every room, and add only a thin floor build-up, letting the design intent carry through uncompromised.
No visible radiators, registers, or wall units
Thin 1 to 2 inch floor build-up preserves ceiling height
Near-silent operation at roughly 20 dB(A)
Proven comfort, not a prototype
Honest, verifiable performance and track-record facts, with no fabricated statistics or testimonials.
690,000 sq ft
Installed across
~2017
In service since
Rated to −13 °F
Cold-climate rating
COP up to 4.6
Efficiency
Frequently Asked Questions
About 1 to 2 inches — much thinner than a poured hydronic slab — so ceiling heights, thresholds, and sightlines are preserved.
Yes — there is no water in the floor to leak, and it works with a wide range of finished floor materials. We confirm the build-up and finish compatibility for your specification.
Capabilities for Home Designers & Architects
You Might Also Be Interested In
Waterless Radiant Floor Heating
Learn more about our waterless radiant floor heating solutions.
Read more →Heat, Cool & Hot Water — One System
Learn more about our heat, cool & hot water — one system solutions.
Read more →5-Constant Comfort
Learn more about our 5-constant comfort solutions.
Read more →High-End & Custom Homes
Solutions tailored for the high-end & custom homes industry.
Read more →Contact Us
Get in touch or request a quote.
Read more →Blog
Read the latest articles and industry insights.
Read more →Design comfort in from the start
Talk to us about fit, floor build-up, and specifying HT on your next project.